Betslip Printing.

You need to setup your printer to match the betslip. Usually you only need to do this only once, but sometime due to the roller of the printer wear and tear, you may have to adjust it from time to time. The values of the setting are in ISO standard (millimeter). The layout will be difference for each country lottery game. WinTOTO provide a flexible aligning technique that allow you to define majority of the betslip marking.

 
  1. This is the “A” dimension from the edge of the paper to the first center of the mark.
    Try to increase or decrease this value by 0.5mm slowly.
  2. This is the “B” horizontal dimension between the two horizontal marks.
    This value must be increase by 0.01mm step by step. A micro adjustment can mean big changes if the horizontal tick is longer.
  3. This is the “C” vertical dimension between the two vertical marks.
    This value must be inrease by 0.01mm step by step.
  4. This is the “D” dimension from the bottom edge of the paper to the first center of the mark.
    Try this measure from the edge of the betslip to the first mark using a mm rular.
  5. This is the number of vertical marks per board.
    Take a look at the example of the betslip as shown above.
  6. This is the number of horizontal marks per board.
    This is the narrower mark as shown.
  7. This is the number of horizontal board per betslip. Each board mean each section or each ticket.
    Take a look at the picture at "P".
  8. This is the number of vertical board per betslip. Each board mean each section or each ticket.
    Take a look at the picture at "P".
  9. After every setting is confirmed correct, you can click this OK button to save the betslip setting.
  10. Apply will make sure the changes you made are recorded in the system, not save yet.
  11. To test the printing of the betslip, insert an original betslip into your printer tray, click this button and start printing. Check the print out and measure the marked position, adjust the value accordingly. If you have difficulty in adjusting the marking, please scan and email the sample of the printout together with your setting value to our technical staff, they can help you.
  12. You may cancel the changes anytime by clicking here.
  13. This is the thickness of the mark. The default is 1mm. It is best to keep this mark as thin as possible.
  14. This is the length of the mark.
  15. Some betslip need to tick which system, enable will mark this place (For singapore system only).
  16. An orientation of the Betslip.
  17. Dim G is the gap between each group of board in horizontally across. Usually, it is about twice the value of Dim "B". But if there is only 1 section, then it doesn't take into account of the value.
  18. Dim H is the gap between each group of board in vertical across. Usually it is about twice the value of Dim "C". But if there is only 1 section, then it doesn't take into account of the value.
  19. Number Direction is referring to the direction of the number layout within the board. The example above is a horizontal layout inward. But some board is vertically downward.

Some Sample setting for the various printer.

Singapore Betslip 6/45 Game

Dimension
Canon i6500
Canon IP1000/i225
Epson CX3100
A
22.5
24.0
24
B
4.55
4.55
4.55
C
6.37
6.37
6.37
D
10.5
10.5
10.5
E
5
5
5
F
9
9
9
G
9.5
9.5
9.5
H
12.7
12.7
12.7
Mark Thickness
1
1
1
Mark Length
2
2
2
Horizontal
3
3
3
Vertical
2
2
2
No. Direction
Horizontal
Horizontal
Horizontal

Malaysia Game Betslip 6/42

Dimension
Canon i6500
Canon IP1000/i225
Epson CX3100
Canon 400sp
A
41.5
42
42
41.5
B
4.07
4.07
4.07
4.07
C
6.37
6.37
6.37
6.37
D
11
11
11
7.8
E
10
10
10
10
F
5
5
5
5
G
8
8
8
8
H
12.5
12.5
12.5
12.5
Mark Thickness
1
1
1
1
Mark Length
2
2
2
2
Horizontal
6
6
6
6
Vertical
1
1
1
1
No. Direction
Vertical
Vertical
Vertical
Vertical